Campbell-hausfeld COM220 Instrukcja Użytkownika

COM220 Telephone ModemRevision: 3/07Copyright © 1997-2007Campbell Scientific, Inc.

COM220 Telephone Modem CAMPBELLSCIENTIFICINC.CR10MADE IN USAWIRING PANEL NO.EARTHDIFFSEAG H L AG H L AG H L AG GGE3 AG4 5 678 910 1112GGGG12V 12VSWITC

COM220 Telephone Modem You can modify the following COM220 settings with DIP switches: 1) Communication mode (e.g., SDC or Modem Enable) 2) ME baud ra

COM220 Telephone Modem 3) If using a non-PakBus datalogger (e.g., CR510, CR10X, CR23X, CR7, CR5000), verify that DIP switch 1 on the COM220 is in the

COM220 Telephone Modem in Setup’s PakBusPort [LoggerNet, Setup, PakBusPort (in the device map)] may limit the baud rate selected by the modems since i

COM220 Telephone Modem This is a blank page. 10

Appendix A. Changing COM220 Settings Changing any of the modem's settings may result in communication problems. After changing the settings, t

Appendix A. Changing COM220 Settings TABLE A-1. Selecting ME Baud-rates via DIP Switches 3 and 4 ME Baud-rate Switch 3 Switch 4 9600 Open Open 38

Appendix A. Changing COM220 Settings FIGURE A-1. COM220 to Computer Connection To configure the COM220 with Hayes AT commands, follow these steps:

Appendix A. Changing COM220 Settings 7) Follow the instructions that appear in the terminal emulator screen (Figure A-3). 8) Be sure to save all n

Appendix A. Changing COM220 Settings FIGURE A-3. Terminal Emulator Screen in Device Configuration HAYES AT COMMAND SUMMARY: This manual does not at

Warranty and Assistance The COM220 TELEPHONE MODEM is warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in materials and workmanship unde

Appendix A. Changing COM220 Settings M0 Speaker always off M1 (default) Speaker on during call establishment M2 Speak on during entire call sessio

Appendix A. Changing COM220 Settings FIGURE A-4. Send OS Screen in Device Configuration A.4 Program Examples A.4.1 ModemCallback Example (for CR1

Appendix A. Changing COM220 Settings ModemCallBack(Result,ComSDC7,9600,0,"5551212","",40,60,Abort) CallTable Test5 NextScan

Appendix A. Changing COM220 Settings The COM220 can return several possible responses once connected (each terminating in a carriage return): CAUTION

Appendix A. Changing COM220 Settings Do not put Instruction 97 inside a loop or conditional statement; it must be executed each time the table is run

Appendix A. Changing COM220 Settings 12: Initiate Telecommunications (P97) 1: 22 Phone Modem/9600 Baud ;set baud-rate/modem 2: 5 Disabled

Appendix A. Changing COM220 Settings SequentialMode DataTable (TestA,1,-1) DataInterval (0,2,Sec,10) Minimum (1,BatteryVoltage,FP2,0,False) Sample

Appendix B. CS I/O Connection B.1 CS I/O 9-Pin Connection The pin out of the connector is shown in Figure B-1. The direction of the signal relative

This is a blank page.

Appendix C. Theory of Operation C.1 Theory of Operation The COM220 modem is used to transmit data over bandwidth-limited channels such as telephone

COM220 Telephone Modem Table of Contents PDF viewers note: These page numbers refer to the printed version of this document. Use the Adobe Acrobat®

This is a blank page.

Appendix D. FCC Warning to Users of Class B Computing Devices This equipment generates, uses, and can radiate radio frequency energy, and if not ins

This is a blank page.

Appendix E. IC Information Industry Canada (IC) was formerly known as DOC. NOTE CP-01, Issue 8, Part I Section 14.1 “NOTICE: The Industry Canada la

This is a blank page.

This is a blank page.

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com info@campbells

COM220 Telephone Modem Table of Contents D. FCC Warning to Users of Class A Computing Devices...D-1 E. IC Information ...

COM220 Telephone Modem 1. Introduction 1.1 General Description The COM220 modem is a selectable-baud-rate modem employing the Hayes AT command set.

COM220 Telephone Modem The COM220 is connected to a CSI datalogger by a 9-pin subminiature D cable. This is the same 9-pin CS I/O interface common to

COM220 Telephone Modem 2. Specifications • Standards: V.92, K56Flex, V.90, V.34, V.32bis, V32, V23, V22bis, V22, V.21, B212, B103 • Registration:

COM220 Telephone Modem TABLE 1. Dataloggers that Require Direct 12 VDC Connection to COM220 CR10(X) with silver wiring panel CR10(X) with black CR10

COM220 Telephone Modem SE12 34 56 78H1234LDIFFHEX1HLHLLP2P112VGDC ONLYCAUTIONLUGGROUNDPOWER INWIRING PANELCR1000PERIPHERAL PORTRS-232 (Not Isolated)SN